Releases

Help / The settings, one by one / Common Interface

Common Interface

Screenshots are being added: so far 0 from the receiver and 0 from the web interface; the aim is at least 5 of each, with arrows and frames, and, where a setting changes what you see, a before and after comparison.

What it is for

The screen shows the receiver's Common Interface (CI) slots and the module in each one: whether it is found, whether it is ready and what it is called.

From here you turn each slot on or off, open the module's menu, reset it, choose which channels it receives, store the card's PIN code and see whether the module works as CI+.

At the top there are two settings shared by all slots (the CI delays); each slot has its own settings: the module's messages, decoding several channels, the bit rate and, on some receivers, PID routing.

The same slots and settings are in the web interface, on the /common-interface page, where you also add the CI+ certificates. The module's menu is used only on the TV.

How to get here

Path: Main menu > Settings > Conditional access > Common Interface (the fourth row).

Keys on the remote: MENU 6 6 4.

The row appears only on receivers that have at least one CI slot, also when the slot is empty.

In the web interface: the /common-interface page.

What you see on the screen

At the top, a line that says where the cursor is: “Common settings”, “Slot 1”, “Slot 1 - module disabled” or, on some rows, what OK does there.

The first rows are the common settings: “DVB CI Delay” (only on receivers that have it) and “CI start delay”.

Then, for each slot: the title “Slot 1”, “CI enabled”, “Reset”, “Init”, the module row (its name when it is ready, “init module” while it starts, “no module found” when the slot is empty), “Assign channels to module”, “Store PIN code”, “Enter stored PIN code”, “Delete stored PIN code” (only when one is stored), “Show CI messages”, the CI+ row, “Multiple service support” and, on receivers that have them, “High bitrate support” and “Relevant PIDs Routing”.

A slot with “CI enabled” set to No has only its title and the “CI enabled” row: the other rows would do nothing.

The CI+ row shows the state: “CI+: the device certificates are missing”, “CI+: the certificates are in place; the module works as plain CI”, “CI+: authentication in progress” or “CI+: authenticated, CI+ descrambling”. With the certificates in place, “Disable operator profiles” and “Descrambling options” appear below it.

The module's menu, opened with OK on its name, has the title and the texts sent by the module, its list of choices and a bottom line; while it waits for an answer it shows “wait for ci...”, and when it asks for a code it shows “please press OK when ready”.

“Assign channels to module” opens a window with “Add channel”, “Add provider”, “Add CAID” and, below them, the current assignments (“Channel: ...”, “Provider: ...”, “CAID: ...”); at the bottom a help text and the keys RED “Close”, GREEN “Save”, YELLOW “Delete”.

Rows and settings

RowValuesDefaultWhat it does
DVB CI Delay16, 32, 64, 128, 256256A driver setting for the stream that goes through the module. The row appears only on receivers that have it. Leave the factory value if the picture works.
CI start delay0 s ... 15 s5 sHow many seconds after the receiver starts the work with the CI modules begins. When a module is not found after the receiver starts, but is found after “Init”: increase it.
CI+ helper (needs a receiver restart)Yes, NoYesAppears only if you installed an external CI+ helper program yourself (the image does not have one). When on, it takes care of the module, and “Reset” and “Init” are hidden.
CI enabledYes, NoYesNo: the receiver stops talking to the module in the slot. The slot no longer receives any channel and the module's menu no longer opens; the saved assignments remain for when you turn it on again. When you want a channel to stop going through the module, without removing it.
ResetOK sends the reset command to the module in the slot. It also deletes the remembered CI+ authentication, so a CI+ module authenticates again. When the module no longer answers or no longer decodes.
InitOK starts the initialisation of the module again. When the module stays on “init module”.
The module rowthe module name, init module, no module foundThe state of the module in the slot. When the module is ready, OK on its name opens the module's menu: UP and DOWN choose, OK answers, EXIT goes one step back in its menu, and when the module asks for a code you type it with the digits.
Assign channels to moduleAdd channel, Add provider, Add CAIDno assignments: the module is chosen by itselfSays which channels the module in this slot receives: particular channels (chosen from the channel list), all the channels of a provider (from the Providers list or the provider of a chosen channel) or the channels with a particular access system (CAID: from the list of those known to the module and to the channel that is playing, or typed with 1-4 hexadecimal digits, for example 0B00; keys 2 and 3 also give the letters A-F). YELLOW deletes the selected assignment. GREEN saves; the assignments can also be prepared with the module removed, and they are used when the module is ready. When you have two modules and want each one to receive only its own channels.
Store PIN codeYes, NoYesYes: the PIN code you type when the module asks for it is remembered, without a question, and next time the module receives it by itself. If the module asks for it again within a minute of receiving it, the stored code is probably wrong: the receiver stops sending it and asks you, so the card does not get blocked. Choose “No” when you want to type the code every time.
Enter stored PIN codeOK: you type the card's PIN code (4-8 digits); the module receives it by itself when it asks for it. When you know the code in advance and do not want to wait for the module to ask.
Delete stored PIN codeAppears only when a code is stored. OK deletes it; the module will ask for the code on screen again. When you changed the card's code or the stored one is wrong.
Show CI messagesYes, NoYesNo: the messages sent by the module no longer appear on screen by themselves. The PIN request still appears when no code is stored. When the module often shows messages that get in your way.
The CI+ rowCI+: the device certificates are missing, CI+: the certificates are in place; the module works as plain CI, CI+: authentication in progress, CI+: authenticated, CI+ descramblingThe slot's CI+ state. OK says what CI+ does, which files are missing and how to add them. Without the device certificates the module works as plain CI, as before, if it can.
Disable operator profilesNo, YesNoAppears only with the CI+ certificates in place. Yes: the receiver no longer takes the operator profile (its channel list and names) from the module. When the operator profile gets in the way of your own channel list.
Descrambling optionsOff, Close the CA device at the end of the programme, Shifted CA device index, Shifted and closed at the endOffAppears only with the CI+ certificates in place. Adjustments for CI+ modules that do not descramble correctly with the factory value. Only when an authenticated CI+ module gives a black screen; try the other values one by one.
Multiple service supportAuto, No, YesAutoWhether the module can decode several channels at once (for example one channel you watch and one you record). Choose “No” when your module decodes only one channel at a time and “Yes” when you know it can do more.
High bitrate supportNormal, High, Extra HighNormalThe speed at which the receiver sends the stream to the module. The row appears only on receivers that have this choice, and “Extra High” only where the driver has it. When your module needs a higher speed (its maker says so).
Relevant PIDs RoutingNo, YesNoYes: only the streams the channel needs go through the module. The row appears only on receivers that have it. When the module cannot cope with all the streams of a transponder.

Keys

UP / DOWNMove the cursor to another row; the top line shows the slot of the selected row or what OK does there.
OKDoes what the row says: resets, initialises, opens the module's menu or the assignments, types or deletes the stored PIN code, shows what CI+ does.
LEFT / RIGHTOn settings (the common ones, “CI enabled”, the PIN code, the messages, the bit rate): change the value, which is saved immediately.
EXIT or BackCloses the screen. In the module's menu: one step back in its menu. In the assignments: Close, without the unsaved changes.
Digits 0-9 (in the module's menu)Type the code the module asks for; then OK.
GREEN / YELLOW / RED (in the assignments)GREEN saves the assignments (or “Retry” applying them), YELLOW deletes the selected assignment, RED closes the window.
HELPOpens this help page.

Step by step

Opening the module's menu

  1. Insert the module into the slot and press MENU 6 6 4.
  2. Wait until the module row shows its name, not “init module”.
  3. Move the cursor to the module name and press OK. Choose with UP, DOWN and OK; leave with EXIT.

Giving a module only certain channels

  1. On the module's slot, move the cursor to “Assign channels to module” and press OK.
  2. On “Add channel” press OK and choose the channel from the list (or “Add provider” for all the channels of a provider).
  3. Press GREEN. The assignment is used from the next channel change.

Turning a slot off without removing the module

  1. Move the cursor to the slot's “CI enabled”.
  2. Press LEFT or RIGHT until it says No. The top line says “Slot 1 - module disabled”.
  3. To turn it on again, set “CI enabled” to Yes.

Storing the card's PIN code

  1. Leave “Store PIN code” on Yes (the factory value).
  2. When the module asks for the code, type it once with the digits and press OK. From now on it receives it by itself.
  3. Or type it in advance: OK on “Enter stored PIN code”, the digits, OK.

Turning on CI+ with your own certificates

  1. You need four device files: param, root.pem, customer.pem and device.pem. The image does not have them and we cannot give them to you.
  2. On a phone or computer, open the receiver's /common-interface page.
  3. On the “CI+” card, choose the four files at once and press “Add the certificates”.
  4. The modules restart by themselves. The CI+ row changes to “CI+: authentication in progress”, then to “CI+: authenticated, CI+ descrambling”.
  5. Without a browser: copy the four files by FTP into the receiver's /etc/ciplus folder, then choose “Reset” on the slot.

Problems and solutions

The module row says “no module found”.

The slot is empty or the module is not inserted properly. Remove it, insert it again all the way, then choose “Init”.

The row stays on “init module”.

The module is still starting. Wait a little; if it does not pass, choose “Reset” or “Init”. The assignments and turning the slot off can also be changed in the meantime.

The slot has only the “CI enabled” row.

The slot is turned off. Set “CI enabled” to Yes.

The CI+ row says “CI+: the device certificates are missing”.

The receiver does not have the device certificates. Without them the module works as plain CI, if it can. OK on the row tells you which files are missing; you add them from the /common-interface web page (the “CI+” card) or by FTP into /etc/ciplus.

Where do I get the CI+ certificates?

Not from us. The CI Plus organisation issues them only to receiver makers, for each device; no image can give them. The image has no certificate and does not send your files anywhere: they stay only on the receiver.

The certificates are in place, but it says “the module works as plain CI”.

The module did not authenticate as CI+: it is not a CI+ module or the certificates do not match. Choose “Reset” on the slot; if it stays the same, the module works as plain CI, if it can.

The card asks for the PIN code every time.

Set “Store PIN code” to Yes and type the code once. If the module asks for it again right after receiving it, the stored code is wrong: choose “Delete stored PIN code” and type it again.

The module's messages no longer appear.

“Show CI messages” is set to No. Set it to Yes.

I do not see “Reset” and “Init”.

You installed an external CI+ helper program and “CI+ helper” is set to Yes: then that program resets and initialises the module.

I do not have the “Common Interface” row in the menu.

The row appears only on receivers that have a CI slot.

I saved the assignments and it says “Saved, not applied.”

The assignments were kept, but the module has not received them yet. Press GREEN (“Retry”); if it does not work, check the module. Close keeps what was saved.

It says “Invalid CAID. Use 1-4 hexadecimal digits, for example 0B00.”

Type the code with the digits 0-9 and the letters A-F (keys 2 and 3 on the remote), at most four characters.

It says “The selected channel has no provider. Choose a provider from the Providers list.”

In “Add provider”, open the Providers list and choose the provider there.

I changed the assignments, but the current channel works as before.

The assignments apply from the next channel change. Change the channel and come back.

I cannot find the module's menu in the web interface.

The module's menu is used only on the TV: reading it from the web could take the message meant for the TV.

Related topics

Differences between receivers

The number of CI slots depends on the model (at most four); without any slot the row is missing from the menu. “DVB CI Delay”, “High bitrate support” (and the “Extra High” value) and “Relevant PIDs Routing” appear only on receivers that have these choices.