Releases

Help / The settings, one by one / Channel logos (picons)

Channel logos (picons)

Screenshots are being added: so far 0 from the receiver and 0 from the web interface; the aim is at least 5 of each, with arrows and frames, and, where a setting changes what you see, a before and after comparison.

What it is for

“Channel logos (picons)” puts a set of channel logos on the receiver, without FTP and without a computer: from an address you type or from a USB stick or a disk (an archive or a folder).

The image has no logo sets of its own: you choose where to take them from. Good archives are zip, tar, tar.gz, tar.xz and ipk. From a folder, the .png files in it and in its subfolders are used.

With “Only channels in my list” ticked (Yes by default), only the logos of the channels you have in your list are written, so a large set takes little space. The logos show at once, on the bars, in the channel list and in the guide.

From here you also update the set (from the same source) and uninstall it. Uninstalling deletes only the logos put from this screen; the logos you had before stay.

The first row turns the logos on or off everywhere (the “Channel logos (picons)” setting, Yes by default).

How to get here

Path: Main menu > Settings > Interface & Appearance > Channel logos (picons) (the third row; from 0.7.7, the fourth).

Keys on the remote: MENU 6 4 4 (in 0.7.6: MENU 6 4 3).

From “Channel list settings”: OK on the “Channel logos (picons)” row when the receiver has no logos yet.

In the web interface: the /piconuri page (http://hdsatelit.local/piconuri), where you can also send an archive straight from a computer or a phone.

What you see on the screen

A window titled “Channel logos (picons)”: the list of rows on the left, and on the right four logos from the chosen place (titled “Preview”, or “No logos here yet”).

Below a line, the status: how many logos are in the chosen place, how many were put from this screen and from where, or “Logos are turned off. OK on the first row turns them on.”

At the bottom, the coloured keys: GREEN “From an address”, YELLOW “From a USB stick or disk”, and once you have put a set, also BLUE “Update” and RED “Uninstall”.

While it works, the status shows the step: “Downloading: … of …”, “Reading the archive...”, “Writing logos: … of …”. At the end a message, for example “Done: 312 logos installed.”

YELLOW opens the “Choose the archive or the folder with logos” window: the folders and archives on USB sticks and disks (zip, tar, tar.gz, tar.xz, ipk), the path of the current folder above and, at the bottom, what OK, GREEN and EXIT do there.

Rows and settings

RowValuesDefaultWhat it does
Channel logos (picons): Yes / NoYes, NoYesTurns the logos on or off everywhere: on the bars, in the channel list, in the guide and in the web channel list. When you want no logos on screen.
LocationReceiver memory, Disk or stick: /media/...the place where you already put logos from this screen; otherwise the disk with the most free space; without a disk, the receiver memoryWhere the logos are written. Each place shows its free space and how many logos it already has. When the receiver memory is small and you have a stick or a disk connected.
Only channels in my listYes, NoYesYes: only the logos of the channels in your list are written from the archive. No: the whole set is written. When you want the whole set, for example before a new channel scan.
Install from an addressOpens the keyboard for the archive address (http:// or https://; zip, tar.gz, tar.xz, ipk), then downloads and writes the logos. When you have the address of a logo set.
Install from a USB stick or diskOpens the list of files on the stick or disk: OK enters a folder or picks an archive, GREEN picks the folder you are in. When you have the set on a USB stick.
Update logos (same source)Takes the set again from the same address or path, into the same place. The row appears only after you have put a set from here. When the author of the set has added new logos.
Uninstall logos installed from hereAfter you confirm, deletes only the logos put from this screen. The row appears only after you have put a set from here. When you want another set or want the space back.

Keys

UP / DOWNMove the cursor to another row.
OKDoes what the selected row says (switches Yes/No, chooses the place, starts the installation).
GREENInstalls from an address.
YELLOWInstalls from a USB stick or disk.
BLUEUpdates the set put from here (only after you have put one).
REDUninstalls the logos put from here, after you confirm.
OK (in “Choose the archive or the folder with logos”)Enters the folder or chooses the archive under the cursor (zip, tar, tar.gz, tar.xz, ipk); the installation starts.
GREEN (in “Choose the archive or the folder with logos”)Chooses the folder you are in: the .png logos in it and in its subfolders are taken.
EXIT (in “Choose the archive or the folder with logos”)Back, with nothing chosen.
EXITCloses the screen; an installation already started carries on.
HELPOpens this help page.

Step by step

Putting logos from a USB stick

  1. Copy the logo archive (or the folder with .png files) to a USB stick and plug the stick into the receiver.
  2. Open “Channel logos (picons)” (MENU 6 4 3).
  3. Press YELLOW, enter the stick folder with OK and press OK on the archive (or GREEN in the folder with the logos).
  4. Wait for the message “Done: … logos installed.” The logos show at once.

Sending the archive from a computer

  1. Open http://hdsatelit.local/piconuri in a browser.
  2. Choose the place and leave “Only channels in my list” ticked.
  3. Send the archive from the computer or the phone and watch the status on the page (it also shows on the TV).

Problems and solutions

The message “The archive has … logos, but none of them match the channels in your list.”

The set is for other satellites or another provider. Take another set or untick “Only channels in my list”.

The message “Your channel list is empty.”

Scan for channels first or untick “Only channels in my list”.

The message “Not enough space: … needed, … free.”

Choose a stick or a disk under “Location”, or keep “Only channels in my list” ticked.

The message “The file is not a known archive (zip, tar, tar.gz, tar.xz, ipk).”

Unpack the archive on a computer and put the folder with the .png files on the stick, then pick the folder with GREEN.

The message “It is already installing. Wait for it to finish.”

Only one installation runs at a time, started from the TV or from the web page. Wait for the final message.

I do not see the logos although they were added.

Check the first row, “Channel logos (picons)”: it must be Yes.

Related topics

Differences between receivers

The screen is new in 0.7.6 and is the same on all receivers. On receivers with little memory, put the logos on a USB stick or a disk.