Vu+ Multi Boot (Kexec)
Screenshots are being added: so far 0 from the receiver and 0 from the web interface; the aim is at least 5 of each, with arrows and frames, and, where a setting changes what you see, a before and after comparison.
What it is for
“Vu+ Multi Boot (Kexec)” installs Kexec multiboot on a Vu+ 4K that starts directly from its own memory: the current image stays in memory as Recovery, and in slots 1, 2 and 3 (and on a USB stick or HDD) you can put other images.
You then choose the image from “Restart into another image” or from the boot menu (the MENU key).
The installation downloads the files of the receiver's kexec-multiboot package from the external feed, writes the Kexec loader to the kernel partition (the current kernel is kept for Recovery) and restarts the receiver. Before writing, the receiver checks the model, the files, the kernel and the free space; if anything is wrong, it writes nothing.
For now the row is hidden for everyone: it appears only on a Vu+ 4K started from its memory, without multiboot, and only when the receiver's kexec-multiboot package is already installed or when the tester trying it has set the test mark (an empty file, following the instructions in the testers' topic on the forum), then chose Restart the interface.
How to get here
Path: Main menu > Power & Restart > Vu+ Multi Boot (Kexec), the row above “Deep Standby (Power Off)”, only when it is shown (see above).
Keys on the remote: POWER held down; or MENU, the last entry; then DOWN to “Vu+ Multi Boot (Kexec)”, OK.
In the web interface: the /alimentare page, the “Vu+ Multi Boot (Kexec)” card, shown under the same conditions.
What you see on the screen
A window titled “Vu+ Multi Boot (Kexec)”: the explanation above, and at the bottom RED “Close” and GREEN “Install”.
If the receiver is not suitable, the reason appears instead of the explanation (for example “Kexec multiboot is already installed on this receiver.”) and GREEN is missing.
During the installation: “Downloading the multiboot files...”, then “Installing Kexec multiboot. Do not turn off the receiver...”, at the end “Kexec multiboot is installed. The receiver restarts.”
Keys
| OK or GREEN (Install) | A single question, then the download, the writing and the restart. |
| RED (Close) or EXIT | Closes; it cannot be closed during the installation. |
| HELP | Opens this help page. |
Step by step
Installing multiboot (tester, on a Vu+ 4K)
- Set the test mark, following the instructions in the testers' topic on the forum, and choose Restart the interface.
- Open Power & Restart (POWER held down, or MENU, the last entry) and choose “Vu+ Multi Boot (Kexec)”.
- Press GREEN and answer Yes to the question. Do not turn off the receiver until it restarts by itself.
- After the restart, the current image is Recovery; you put other images in slots 1, 2 and 3.
Problems and solutions
I do not have the “Vu+ Multi Boot (Kexec)” row.
It is hidden until the first test on a real Vu+ 4K. It appears only on a Vu+ 4K started from its memory, without multiboot, with the kexec-multiboot package installed or with the tester's test mark.
The message “I could not download the multiboot files.”
Check the internet connection and try again; nothing was written to the receiver.
The message “The receiver does not currently boot directly from its memory, so I do not install multiboot.”
The receiver started from a USB stick or from a slot of another multiboot. Start it from its own memory and try again.
The message “The installation failed. The receiver stays as it was.”
A check did not pass; the receiver wrote nothing and starts as before.
Related topics
- Power & Restart (the submenu)
- New image from a USB stick
- Matching web page: /alimentare.
Differences between receivers
Only on Vu+ 4K: Solo 4K, Uno 4K, Uno 4K SE, Ultimo 4K, Zero 4K, Duo 4K and Duo 4K SE, since 0.7.6. On other receivers the row never appears.