Releases

Help / The dish and the channel scan / Blind scan

Blind scan

Screenshots are being added: so far 0 from the receiver and 0 from the web interface; the aim is at least 5 of each, with arrows and frames, and, where a setting changes what you see, a before and after comparison.

What it is for

“Satellite blind scan” finds the transponders on the satellite without knowing the frequencies beforehand: the tuner goes through the whole band by itself and notes every transponder it picks up, with the frequency, the polarisation and the symbol rate.

On the screen you see the list of the satellite's known transponders, each with “found” or “being searched”, and the new ones, which are not in the list, with “new”. At the end, “Scan channels” searches for channels on all of them: the known ones and the new ones.

It is useful when a new transponder is not yet in the satellite's list or when you want to see what the satellite your dish points at really broadcasts.

The dish is not moved: the search is done on the satellite of the current channel or, from 0.7.7, on another satellite of the same dish, chosen in the “Satellite” row (DiSEqC switch or toneburst). The same search can be seen and started from the web interface, on the /oarba page.

How to get here

Path: Main menu > Channel scan > Satellite > Blind scan.

Keys on the remote: MENU 1 1 4.

Before that, start a channel from the satellite you want to search: the search is made on the satellite the dish is pointing at now.

In the web interface: the /oarba page (“Satellite blind scan”), with the same choices and the same list. The “Open on the TV” button opens the screen on the TV, and a search started from the page opens it by itself.

What you see on the screen

At the top, the title “Satellite blind scan”.

The screen has two faces. The first one, the choices: the rows “Satellite”, “Band” (only with an LNB that has two bands), “Polarisations”, “Search steps”, “Minimum symbol rate” and, at the end, “Search now”. Each row has its value on the right.

Below the list: what will be searched and how long it takes (“Passes (band × polarisation): 4. Duration: about 11 minutes.”), what the chosen step does and, with a motorised dish, “The dish is not moved: for another satellite, first start a channel from it.” (from 0.7.7, with a switch the satellite is chosen in the “Satellite” row)

Below that, the status line: “Up/Down selects the row, Left/Right or OK changes, Green starts, EXIT stops.”

The second face, the search: the list of transponders, by frequency, each written as “11778 MHz, V, 27500 kSym/s”, with its state on the right: “found”, “new”, “being searched”, and at the end “not found” or, after a stop, “unverified”. Above the status line it shows “Satellite: ...”.

The status line shows the progress (“Step 1 of 3: 45%. Found: 20, new: 2.”) and, at the end, the result (“Done in 640 s. Found: 50 out of 60 known, new: 3.”).

At the bottom, the colour keys. On the choices: RED “Back”, GREEN “Search now”, YELLOW “Change”. During the search: RED “Stop”. After the search: RED “Back”, GREEN “Scan channels”, YELLOW “Search again”.

Rows and settings

RowValuesDefaultWhat it does
Satellitethe satellite of the current channel, the other satellites you reach without moving the dish, the one the dish points at nowthe satellite of the current channelThe satellite to search. From 0.7.7 you choose it with LEFT, RIGHT, OK or YELLOW among the satellites reached without moving the dish: those behind a DiSEqC 1.0 switch or with toneburst, in the order of the ports; the tuner, the LNB and the switching are those of the chosen satellite. With a motorised dish, with Unicable and on Vu+ Solo SE only the satellite the dish points at now remains. The choice is not remembered: the next time it is again the satellite of the current channel. When the first transponders found match another satellite of the dish better, the screen says “The found transponders show that the dish is on ...” and compares with the list of that satellite. When you want to search another satellite of the same dish. For a satellite the dish has to turn to, first start a channel from it.
BandWhole band (low and high), Only low band, Only high bandWhole band (low and high)Which part of the band is searched. The row appears only when the LNB has two bands (for example a universal LNB); an LNB with a single oscillator has a single band. When you know the transponder you are looking for is in one band only: the search takes half the time.
PolarisationsHorizontal and vertical, Only horizontal, Only verticalHorizontal and verticalWhich polarisations are searched. Each band is gone through once for each chosen polarisation. When you are looking for a transponder with a known polarisation and want a shorter search.
Search steps1: whole band once, 2: and band gaps, 3: gaps twice3: gaps twiceHow thoroughly it searches. Step 1: whole band once, then only where a known transponder is missing. Step 2: and all band gaps, searched again in narrow windows. Step 3: gaps once more, with different margins; the safest and longest. The duration below the list changes with the step. Step 1 when you want a quick result; stay on 3 when you do not want to miss anything.
Minimum symbol rateAny, 1 MSym/s, 2 MSym/s, 5 MSym/sAnyNew transponders with a symbol rate below the chosen one are not shown in the list and are not included in “Scan channels”. All the satellite's known transponders remain. When the list fills up with small transponders that do not interest you.
Search nowOK on this row starts the search, like the GREEN key. The channel on the satellite tuner stops while the search runs and starts again at the end (unless the receiver went into standby in the meantime or you started another channel yourself).
A transponder in the search listfound, new, being searched, not found, unverified“found”: it is in the satellite's list and the search picked it up. “new”: the search picked it up, but it is not in the satellite's list. “being searched”: it is in the list and has not been picked up yet. At the end, the ones not picked up become “not found”, and after a stopped search “unverified” (the search may not have reached them).

Keys

UP / DOWNMoves the cursor to another row (on the choices) or to another transponder (in the search list).
LEFT / RIGHTOn the choices: change the value of the selected row, backwards or forwards. During the search they do nothing.
OKOn the choices: moves the selected row to its next value; on “Search now” it starts the search.
GREENOn the choices: “Search now”, starts the search. After the search: “Scan channels”, opens the usual channel scan on all the satellite's known transponders and on the new ones.
YELLOWOn the choices: “Change”, like OK on the selected row. After the search: “Search again”, takes you back to the choices.
RED or EXITDuring the search: “Stop”, stops the search after the band slice being searched now and stays on the list of what was found. Otherwise: “Back”, closes the screen.
HELPOpens this help page.

Step by step

Searching for the satellite's new transponders and their channels

  1. Start a channel from the satellite you want to search.
  2. Press MENU 1 1 4.
  3. Leave the factory choices (whole band, both polarisations, step 3) and press GREEN.
  4. Wait until it says “Done in ... s.”. New transponders have “new” on the right.
  5. Press GREEN (“Scan channels”) and let the scan finish. The channels found go into the channel list.

Making a short search, on one polarisation

  1. On the choices screen, move the cursor to “Polarisations” and press RIGHT until “Only horizontal” or “Only vertical”.
  2. Move the cursor to “Search steps” and choose “1: whole band once”.
  3. Look at the new duration below the list and press GREEN.

Stopping a search that takes too long

  1. Press RED or EXIT during the search. The status line says “It stops after the band slice being searched now...”.
  2. The list keeps what was found until then; the ones not reached have “unverified”.
  3. You can still scan the channels with GREEN.

Problems and solutions

The GREEN button is missing on the choices, and the reason is written below the list.

The search cannot start on this receiver as it is set up: “The receiver has no satellite tuner.”, “The satellite tuner has no satellite configured. Set up the dish in “Tuner settings”.” or “Blind scan doesn't work through a Unicable LNB.” For the second case, set up the dish in Tuner settings.

It says “The LNB oscillator is not known. Check the LNB in LNB configuration.”

The screen does not know the frequencies of the LNB oscillator, so it does not know which band to search. Open LNB configuration and check the satellite's LNB.

It says “The satellite tuner is in use right now (a recording or another screen).”

A recording or another screen is holding the tuner. Try again after the recording ends or after you close the other screen.

It says “The blind scan doesn't work yet on this receiver's tuner.”

The tuner of this model is not yet known to the blind scan program. Search for channels with “By satellite” or “By transponder”.

It says “The blind scan program isn't installed on this receiver. The software update brings it.”

Update the image from Software update and open the screen again.

The search ended quickly and found nothing.

If the first pass picks up no transponder on the whole band, the search stops: the dish receives nothing on that satellite. Check the dish with Signal finder and start a channel from the satellite you want.

Some transponders are left as “not found”.

The search did not pick them up. Search again with “Search steps” set to 3, the safest. In any case, “Scan channels” also goes through them, with the data from the satellite's list.

It says “The search took too long and was stopped.”

The program has a time limit. The transponders found until then remain and you can scan them; for the rest, search again on one band or one polarisation only.

I closed the screen during the search.

The search goes on. You can see it on the /oarba web page or by opening the screen again; at the end, the previous channel starts again.

The screen shows a different satellite than I expected.

The search is made on the satellite of the channel that is playing, and the dish is not moved. Exit, start a channel from the satellite you want and open the search again.

On Vu+ Solo SE it says “Preparing the blind scan: ...” with a step and a time.

From 0.7.7, on the first search the receiver fetches by itself from the feed the search program for the Vu+ tuner: it reads the list of programs, downloads it from the internet if needed, waits for another installation and installs the program; the search then starts by itself. If a step fails, the screen says why (for example a list that cannot be read or the time limit): check the internet and try again.

Related topics

Differences between receivers

The blind scan works only on the tuners known to its program; on the other models the screen says “The blind scan doesn't work yet on this receiver's tuner.”

The “Band” row appears only when the satellite's LNB has two bands.