HD Satelit 0.7.4 pentru Vu+ Ultimo4K

Este prima imagine HD Satelit pentru acest receptor.
Alfa, doar pentru testeri. E o familie nouă de procesoare pentru noi (Broadcom ARM), la care n-am
avut niciun receptor, deci orice e posibil. Cine o instalează își asumă rolul de tester.

Arhiva e numai pentru Vu+ Ultimo4K. Nu o pune pe alt receptor.
Se pune numai de pe stick, de încărcătorul receptorului. Actualizarea imaginii din meniu nu
recunoaște această arhivă. Înainte fă o copie a setărilor și a canalelor din imaginea de acum.
1. Pe un stick FAT32 (cel mult 32 GB) copiezi în rădăcină dosarul vuplus din arhivă, ca pe stick
să fie vuplus/ultimo4k/ cu toate cele 8 fișiere, inclusiv mkpart.update, reboot.update și
hdsatelit-model. Nu le redenumi.
2. Oprești receptorul din întrerupătorul din spate, scoți celelalte dispozitive USB, bagi stickul
într-un port USB al receptorului și pornești receptorul din spate.
3. Când pe afișaj apare Update! Press Power, apeși în 5 secunde butonul Power de pe receptor (pe
receptor, nu pe telecomandă).
4. Receptorul scrie imaginea și repornește singur. După ce arată că a terminat, scoți stickul, ca
să nu înceapă din nou scrierea.
Cât timp receptorul scrie imaginea, nu opri curentul și nu scoate stickul. Păstrează arhiva USB a
imaginii de acum: înapoi la ea ajungi tot de pe stick, dar revenirea nu a fost probată pe acest
receptor.

Dacă la prima pornire apare mesajul că receptorul nu se potrivește, trimite-ne valorile de pe
ecran.

Pașii pe larg: https://stb.hdsatelit.com/receptoare/vu-ultimo4k/descarca/
Suma arhivei, pe Windows, în PowerShell:
  Get-FileHash .\hdsatelit-0.7.4-vuultimo4k-20261113.zip -Algorithm SHA256
Ce aduce imaginea: JURNAL-0.7.4.txt, lângă acest fișier.
Imaginea vine fără nicio garanție (GPLv2). Codul sursă:
https://github.com/monea-software/hdsatelit-enigma2

----------------------------------------

HD Satelit 0.7.4 for Vu+ Ultimo4K

This is the first HD Satelit image for this receiver.
Alpha, for testers only. This is a new processor family for us (Broadcom ARM) and we have never
had one of these receivers, so anything can happen. If you install it, you are a tester.

This archive is only for the Vu+ Ultimo4K. Do not put it on any other receiver.
It installs only from a USB stick, by the loader of the receiver. Updating the image from the menu
does not recognise this archive. Back up the settings and channels of your current image first.
1. On a FAT32 stick (32 GB at most) copy the vuplus folder from the archive to the root, so the
stick has vuplus/ultimo4k/ with all 8 files, mkpart.update, reboot.update and hdsatelit-model
included. Do not rename them.
2. Switch the receiver off with the rear power switch, unplug any other USB device, plug the stick
into a USB port of the receiver and switch the receiver on at the back.
3. When Update! Press Power appears on the display, press the Power button on the receiver within
5 seconds (on the receiver, not on the remote control).
4. The receiver writes the image and restarts by itself. When it shows that it has finished,
remove the stick, so the writing does not start again.
While the receiver writes the image, do not cut the power or remove the stick. Keep the USB
archive of your current image: you go back to it from a stick as well, but going back has not been
tested on this receiver.

If the first start shows a message that the receiver does not match, send us the values on the
screen.

Full steps: https://stb.hdsatelit.com/en/receptoare/vu-ultimo4k/descarca/
Archive checksum, on Windows, in PowerShell:
  Get-FileHash .\hdsatelit-0.7.4-vuultimo4k-20261113.zip -Algorithm SHA256
What the image brings: JURNAL-0.7.4.txt, next to this file.
The image comes with no warranty (GPLv2). Source code:
https://github.com/monea-software/hdsatelit-enigma2
